Before you start…

You’re almost ready… And then you realise you don’t have any instructions near you. Don’t stress just yet; down here you will find the paste instructions of our products!

Wallpaper assemblage instruction
Pre pasted wallpaper (with an intergrated adhesive layer!)
Step 1:

The preparation. First, make sure the walls are smooth. Remove all wallpaper, adhesive residue and other blemishes. For a good result the surface should be completely smooth! Make sure that the floor is free and equipped with a waterproof sailing. During application of the photo wall murals you make use of water. As a result, there might be water on the floor.

Step 2:

Draw a vertical line with a perpendicular / level.

Step 3:

For this wallpaper you ONLY NEED WATER. The wallpaper has a pre-glued adhesive side on the back of the wallpaper. Place a container (at least 60 cm wide) in the space where it is to be hung and fill it with water. Then place the first panel in the water for about 20 seconds.

Step 4:

Carefully take the panel out of the water and fold it in first on one side and then on the other side. (pay attention to the wallpaper immediately afterwards)

Step 5:

Hang the first panel against the perpendicular. Make sure you use the right panel (number)! Lay the panel down gently and (without too much pressure) smooth it out from the center to the sides.

Step 6:
Then stick the next panel on the wall in the same way as the previous.
Step 7:

Cut away all the extra material along the ceiling, the plinth and possibly the door jamb with the help of a wallpaper ruler or spatula and a sharp, new hobby knife.

Step 8:
Remove excess glue residues from the wallpaper.
Extra advice for the assembler!
  • DO NOT use wallpaper glue
  • unless otherwise stated on the instruction included, you can stick this photo wallpaper.
  • The wallpaper always comes with a ± 5 cm margin all around.


Non-woven wallpaper (assemble with an adhesive made for non-woven wallpaper)
Step 1:

The preparation. First, make sure the walls are smooth. Remove all wallpaper, adhesive residue and other blemishes. For a good result the surface should be completely smooth! Make sure that the floor is free and equipped with a waterproof sailing. During application of the photo wall murals you might make a bit of a mess.

Step 2:

Draw a vertical line with a perpendicular / level.

Step 3:

For this wallpaper you should use wallpaper glue for non-woven wallpaper, a sharp knife, a squeegee and a level.

Step 4:

Start with covering the wall(!) NOT the wallpaper with the adhesive for non-woven wallpaper.

Step 5:

Hang the first panel against the perpendicular. Make sure you use the right panel (number)! Lay the stroke down gently and (without too much pressure) smooth it out from the center to the sides.

Step 6:

Then stick the next panel on the wall in the same way as the previous lane.

Step 7:

Cut away all the extra material along the ceiling, the plinth and possibly the door jamb with the help of a wallpaper ruler or spatula and a sharp, new hobby knife.

Step 8:

Remove also excess glue residues from the wallpaper.

Extra advice for the assembler!

  • glue the wall with an adhesive for non-woven wallpaper.
  • unless otherwise stated on the instruction included, you can stick this photo wallpaper.
  • The wallpaper always comes with a ± 5 cm margin all around.

YouPri is not responsible for the pretreatment of the walls or the assambling of the wallpaper. As well as the occurrence of consequential and / or consequential damage before, after or during the application of the photo wallpaper.

Applying door stickers
Do you want to know how to apply a door sticker? Read on and you will find the tutorial below!

Before you start, it is important to degrease the surface as well as possible. This is important because the door sticker does not adhere properly on a surface that hasn’t been made fat-free sufficiently.

The Surface Cleaner removes dust, finger- and hand prints and fat without leaving streaks.

How to use:

  • Spray the surface with the surface cleaner.
  • Then rub the entire door.
  • Wait a while and then clean it well with some tissue paper.
  • Done? Wait for at least 5-10 minutes, so the surface has time to dry completely.
  • Afterwards you can start applying the door sticker.

For more information you can click this link.